The annual inspection is due every 12 calendar months for nearly every aircraft. The 100-hour inspection is due every 100 hours of time in service, but only if the aircraft is flown for hire or used for flight instruction for hire that the person provides the aircraft for. Any A&P mechanic can do and approve a 100-hour inspection within the ratings held, but an annual must be performed by a mechanic who holds an inspection authorization (IA) or by another person authorized by 14 CFR 43.7 (14 CFR 91.409).
This guide follows the regulation text as of November 2026 (14 CFR parts 1, 43, 65 and 91). It is study material, not advice on a specific aircraft.
The two inspections side by side
| Annual inspection | 100-hour inspection | |
|---|---|---|
| Rule | 14 CFR 91.409(a) | 14 CFR 91.409(b) |
| Trigger | Within the preceding 12 calendar months | Within the preceding 100 hours of time in service |
| Who it applies to | Any aircraft, unless an exception in 91.409(c) applies | Only an aircraft carrying any person (other than a crewmember) for hire, or one used by a person giving flight instruction for hire in an aircraft that person provides |
| Who may perform it | A person authorized to perform annual inspections (an IA holder under 65.95(a)(2)) | A mechanic with the right rating (65.85, 65.87), an IA holder, or others authorized under 43.7 |
| Scope and checklist | 43.15(c) and Appendix D to Part 43 | 43.15(c) and Appendix D to Part 43 |
| Record entry | 43.11 | 43.11 |
The scope is the same. The difference is the trigger and who is allowed to do it.
What triggers each one
Annual: the calendar. 91.409(a) says no person may operate an aircraft unless, within the preceding 12 calendar months, it has had either of these:
- An annual inspection in accordance with part 43 that has been approved for return to service by a person authorized by 43.7, or
- An inspection for the issuance of an airworthiness certificate in accordance with part 21.
100-hour: the hour meter, but only for hire. 91.409(b) says that, except as provided in paragraph (c), no person may operate an aircraft carrying any person (other than a crewmember) for hire, and no person may give flight instruction for hire in an aircraft which that person provides, unless within the preceding 100 hours of time in service the aircraft has received an annual or 100-hour inspection and been approved for return to service in accordance with part 43, or has received an inspection for the issuance of an airworthiness certificate in accordance with part 21.
“Time in service” is defined in 14 CFR 1.1 for maintenance time records: the time from the moment an aircraft leaves the surface of the earth until it touches it at the next point of landing (14 CFR 1.1). It counts airborne time only.
Notice the “for hire” limit. A privately owned aircraft flown only for the owner’s own use never needs a 100-hour inspection under this rule. It still needs the annual. And the flight instruction wording matters: the 100-hour requirement applies to a person giving flight instruction for hire in an aircraft that person provides. This guide does not try to sort out every real-world case, so take unusual situations to your inspector.
The 10-hour allowance
The 100-hour limit “may be exceeded by not more than 10 hours while en route to reach a place where the inspection can be done.” The excess time “must be included in computing the next 100 hours of time in service” (14 CFR 91.409(b)).
The allowance covers only the time en route to where the inspection can be done, and it applies to the 100-hour limit only. There is no matching allowance in 91.409(a) for the 12 calendar months.
Which one can stand in for the other
An annual satisfies the 100-hour requirement. 91.409(b) accepts “an annual or 100-hour inspection,” so an annual resets the 100-hour clock for an aircraft that is flown for hire.
A 100-hour does not satisfy the annual. The last sentence of 91.409(a) says no inspection performed under paragraph (b) may be substituted for any inspection required by paragraph (a) “unless it is performed by a person authorized to perform annual inspections and is entered as an ‘annual’ inspection in the required maintenance records.”
So there are two conditions, and both must be met:
- The person doing the work must be authorized to perform annual inspections.
- The record entry must call it an “annual.”
If an IA holder does a full inspection but the logbook entry says “100-hour inspection,” it is a 100-hour inspection on paper. The entry is part of the inspection.
Who may perform and approve each
Start with 43.7, which lists who may approve an aircraft for return to service. Under 43.7(b), the holder of a mechanic certificate or an inspection authorization may approve as provided in part 65 (14 CFR 43.7). For the full list, see approval for return to service.
| Who | What part 65 says | Section |
|---|---|---|
| Mechanic with an airframe rating | May perform the 100-hour inspection required by part 91 on an airframe, or any related part or appliance, and approve for return to service | 65.85(a) |
| Mechanic with a powerplant rating | May perform the 100-hour inspection required by part 91 on a powerplant or propeller, or any part thereof, and approve for return to service | 65.87(a) |
| Inspection authorization holder | May “perform an annual, or perform or supervise a progressive inspection according to §§ 43.13 and 43.15” | 65.95(a)(2) |
Two points:
- 100-hour: 65.85(a) states the privilege for the airframe rating, and 65.87(a) states it for the powerplant rating, each limited to its own subject (airframe and related parts or appliances; powerplant, propeller or any part thereof). A mechanic who holds both ratings has both privileges.
- Annual: the part 65 sections on the airframe and powerplant ratings (65.85, 65.87) give the 100-hour privilege, and the annual privilege appears in 65.95(a)(2) for the inspection authorization holder. 43.7(c) also lets a repair station approve as provided in part 145, and the other items on the 43.7 list apply as that section states. Part 145 is outside this guide’s sources, so check it for what a repair station may do.
An IA is an authorization added to a mechanic certificate, not a separate certificate. To be eligible, an applicant must hold a currently effective mechanic certificate with both airframe and powerplant ratings, each in effect for a total of at least 3 years, and meet the other requirements in 14 CFR 65.91(c), including at least 2 years of active maintenance work before applying and a passed written test on inspecting aircraft for return to service.
What Part 43 Appendix D means
Both inspections use the same scope. Under 43.15(c)(1), each person performing an annual or 100-hour inspection must use a checklist. It may be the person’s own, one from the manufacturer, or one from another source, but it “must include the scope and detail of the items contained in appendix D to this part” and the rotorcraft items in 43.15(b) (14 CFR 43.15).
Appendix D is not the checklist itself. It sets the minimum scope and detail that any checklist must include. Its groups are:
- Before starting (App. D (a)): remove or open all necessary inspection plates, access doors, fairing and cowling, and thoroughly clean the aircraft and engine.
- The groups: fuselage and hull (b), cabin and cockpit (c), engine and nacelle (d), landing gear (e), wing and center section (f), empennage (g), propeller (h), radio (i), and (j) any installed miscellaneous item not otherwise covered, for improper installation and improper operation.
Each item is written as a component followed by what to look for. For example, under the engine and nacelle group (d)(3) the inspector checks the internal engine “for cylinder compression and for metal particles or foreign matter on screens and sump drain plugs.” Under the landing gear group (e)(8) the inspector checks tires “for wear and cuts.” Appendix D says each group is inspected “(where applicable),” so the list is applied to the particular aircraft.
43.15(c)(2) adds an engine run. Before approving a reciprocating-engine-powered aircraft for return to service after an annual or 100-hour inspection, the person must run the engine or engines to determine satisfactory performance, in accordance with the manufacturer’s recommendations, of (1) power output (static and idle r.p.m.), (2) magnetos, (3) fuel and oil pressure, and (4) cylinder and oil temperature.
For turbine-engine aircraft, 43.15(c)(3) requires the engine run to determine satisfactory performance in accordance with the manufacturer’s recommendations.
The record entry (43.11)
Inspections under part 91 are recorded under 43.11, not 43.9. The entry must contain (14 CFR 43.11(a)):
- The type of inspection and a brief description of the extent of the inspection.
- The date of the inspection and aircraft total time in service.
- The signature, certificate number and kind of certificate held by the person approving or disapproving for return to service.
- If airworthy: “I certify that this aircraft has been inspected in accordance with (insert type) inspection and was determined to be in airworthy condition,” or a similarly worded statement.
- If not approved because of needed maintenance or noncompliance with applicable specifications, airworthiness directives or other approved data: “I certify that this aircraft has been inspected in accordance with (insert type) inspection and a list of discrepancies and unairworthy items dated (date) has been provided for the aircraft owner or operator,” or a similarly worded statement.
If the inspector finds the aircraft unairworthy or not meeting its type certificate data, airworthiness directives or other approved data, the inspector must give the owner or lessee a signed and dated list of those discrepancies (43.11(b)). For more on the two record rules, see 43.9 vs 43.11 maintenance record entries.
Sample entries (all made up)
These are original examples, not real aircraft. Aircraft, dates, times and certificate numbers are invented.
Annual inspection, airworthy:
November 3, 2026. Aircraft total time in service 3,412.6 hours. I certify that this aircraft has been inspected in accordance with an annual inspection and was determined to be in airworthy condition. The inspection was performed using the manufacturer’s inspection checklist, which includes the scope and detail of items in Appendix D to Part 43. Engine run-up performed and found satisfactory. A&P Mechanic with IA, certificate no. 0000000, IA no. 0000000. [signature]
100-hour inspection, with discrepancies:
November 10, 2026. Aircraft total time in service 3,468.1 hours. I certify that this aircraft has been inspected in accordance with a 100-hour inspection and a list of discrepancies and unairworthy items dated November 10, 2026 has been provided for the aircraft owner. A&P Mechanic, certificate no. 0000000. [signature]
The second aircraft is not approved for return to service until the listed items are corrected. In the first entry, the words “annual inspection” are what let it count as the annual under 91.409(a).
Common mistakes
- Thinking a 100-hour inspection is a lighter annual. The scope under 43.15(c) and Appendix D is the same. The trigger and who is authorized differ.
- Applying the 100-hour rule to every aircraft. It applies only to the for-hire uses in 91.409(b).
- Letting a 100-hour “cover” the annual. Only if an annual-authorized person did it and the entry says “annual.”
- Counting hours wrong. Time in service is takeoff to landing (14 CFR 1.1), and any overage is charged to the next 100 hours.
- Forgetting the exceptions. 91.409(c) removes paragraphs (a) and (b) for aircraft with a special flight permit, a current experimental, light-sport or provisional airworthiness certificate, aircraft under an approved part 125 or 135 inspection program, and aircraft under progressive inspection or the large and turbine program in (d) and (e).
Try one (an original question)
A flight school rents out a training airplane for instruction for hire. It has 99.0 hours of time in service since its last 100-hour inspection, and the shop is 1.5 hours away. May it fly to the shop?
Yes. 91.409(b) allows the 100-hour limit to be exceeded by not more than 10 hours while en route to reach a place where the inspection can be done. It would arrive at 100.5 hours, and the 0.5 hour of excess counts toward the next 100 hours.
A short study plan
- Write the two triggers from 91.409(a) and (b) on one line each.
- Memorize who does the annual (IA, 65.95(a)(2)) and the 100-hour (airframe rating 65.85(a), powerplant rating 65.87(a)).
- Write one sample entry for each inspection from memory, then check it against 43.11(a).
- Practice the General test’s regulations questions: Regulations, Maintenance Forms, Records, and Publications.
Common questions
Who can sign off an annual inspection?
A person authorized by 43.7. In practice for a mechanic, that is an inspection authorization holder, who may perform an annual under 65.95(a)(2). A repair station may approve as provided in part 145 (43.7(c)).
Can I go over 100 hours to reach a shop?
By not more than 10 hours, and only while en route to reach a place where the inspection can be done. The excess counts toward the next 100 hours (14 CFR 91.409(b)).
Does my own aircraft need a 100-hour inspection?
Not unless it is used for hire as 91.409(b) describes. It still needs an annual within the preceding 12 calendar months, unless a 91.409(c) exception applies.